We use cookies to provide you with a better experience. If you continue to use this site, we'll assume you're happy with this. Alternatively, click here to find out how to manage these cookies

hide cookie message
Contact Forum Editor

Send an email to our Forum Editor:


PLEASE NOTE: Your name is used only to let the Forum Editor know who sent the message. Both your name and email address will not be used for any other purpose.

Speakers Corner


It's free to register, to post a question or to start / join a discussion


 

Central Heating Pipe Power Jetting?


spuds
Resolved

Likes # 0

Perhaps a topic for discussions, due to the changeable and cold weather, and how we all like to keep warm?.

Having had problems with the central heating over the past few months, which as resulted in having a circulating pump and boiler fan replaced. Today having had no heating etc for a few days, the engineer (very busy) called and stated that the problem was actually sludge in the system.

He as arranged for the whole system to be power flushed, and other pipework and some fitments replaced next week.

Have you had this done, did it make a vast improvement, and were there any later problems. Not forgetting how some of us neglect our central heating until things go seriously wrong?.

Like this post
Forum Editor

Likes # 0

Power flushing is not a cheap, or rapid operation if done properly, but it almost invariably has a considerable beneficial effect.

On completion corrosion inhibitor should be added to the system.

Like this post
carver

Likes # 0

spuds not being funny but how did he come to this conclusion as F.E has said it's not cheap.

Like this post
wiz-king

Likes # 0

I had my 25 year old system power flushed and the amount of muck it shifted was enormous. I also had a centrifugal filter fitted and that took out a load of larger lumps of scale and stopped the pump from getting blocked.

Like this post
onthelimit1

Likes # 0

My (17 yr old) oil fired boiler was getting noisy - 'kettling', a plumber told me. On his advice, I treated the system with Fernox , there are others available. The colour of the water when I drained it down the second time was amazing. It did stop the noise, but can't really judge if the system is more efficient or not.

Like this post
john bunyan

Likes # 0

I had this done and they fitted a magnetic? filter with a drain valve so on annual servicing the sludge collects there and is drained off (near the boiler.)

Like this post
Fruit Bat /\0/\

Likes # 0

Sludging can cause cold spots on radiators I have removed mine and parents and flushed out (not system power flush) and it made a big difference.

Last summer changed my boiler and fitted 5 new rads (other two were only 2 years old) new ones seem to get a lot hotter, perhaps due to lesss layers of paint :0)

Like this post
flycatcher1

Likes # 0

Last year we had a new boiler fitted by British Gas. A power flush was deemed mandatory. The engineer did not carry out the flush as he said that it was unnecessary. As we had paid for it I complained to the powers and then received a full power flush, took six hours, system greatly improved. We had a magnetic filter fitted as part of the original deal.

As the result of my complaint we received a small refund, a new thermostat and two new thermostatic radiator valves. The engineer also cocked up the condensing pipe fit but BG soon sorted that as per correct spec.

We have micro bore piping but the power flush did shift a fair amount of sludge.

Like this post
woodchip

Likes # 0

Best way is to remove each Rad and flush with a Hose, then as FE says it need an inhibitor in it o stop it happening again Steel Panels Brass fittings anf copper pipes all add up to corrosion due to Electro-osmosis of different metals additives stop this. that one of the reasons you get rusty cars

Like this post
Bing.alau

Likes # 0

Fruit bat. Did removing your parents really help? Sorry but I just couldn't resist that remark..

Like this post
lotvic

Likes # 0

Had mine (rads not parent) power flushed by BG last monday, took all day. It was deemed necessary by BG Engineer who did Annual Service as had major cold spots at middle and bottom of some rads and closer investigation colour of water was rusty red. I have a Magnaclean trap fitted and that also was full of gunge. Top of rads were hot, cold spots were due to build up of sludge.

I had paid for a power flush Dec 2009 when had new boiler fitted and couple of rads changed, so this time it didn't cost me anything as was still covered (and also service agreement) It was suspected that the 2009 flush wasn't done properly.....

I spent prior week having to have rads on full heat to circulate the flushing stuff to dislodge the sludge before the powerflush could be done and the old water washed out and replaced with new clean water and inhibitor fluid added.

Despite all promises, I am now finding system doesn't seem to be balanced very well so am fed up with it. If I have them all on, one rad doesn't get hot. If I turn another off then the cold one does get hot etc etc. I also had a lot of air to bleed from one rad as the new water settled (I had been expecting that, so ok)

Overall, yes it is working better now, if only it had been properly balanced I'd be happy with it.

Like this post

Reply to this topic

This thread has been locked.



IDG UK Sites

Best camera phone of 2015: iPhone 6 Plus vs LG G4 vs Galaxy S6 vs One M9 vs Nexus 6

IDG UK Sites

In defence of BlackBerrys

IDG UK Sites

Why we should reserve judgement on Apple ditching Helvetica in OS X/iOS for the Apple Watch's San...

IDG UK Sites

Retina 3.3GHz iMac 27in preview: Apple cuts £400 of price of Retina iMac with new model