It's free to register, to post a question or to start / join a discussion
Connecting WIMAX internet to ADSL router
Likes # 0
Posted March 12, 2013 at 1:36PM
I have a Wimax internet connection via an ethernet cable from a small roof top receiver dish. Inside the house the cable (RJ45) is plugged into the POE slot on one side of a small electrically powered black box, and from the other side, an ethernet cable (RJ45), connects to my PC.
I want to share my internet connection with my HTC mobile and would prefer to make use of an existing Belkin 54g ADSL2 modem/wireless router (Belkin F5D7633) if I can. As this router's incoming port is specifically for ADSL my internet RJ45 cable can not plug into it. I have been advised that I can still utilise the router part of the Belkin though, using my PC as an access point, by plugging the ethernet cable from the PC side of the little black box into LAN 1 on the router, then joining the PC to LAN 2 of the router with another ethernet cable.
This worked well at first. I did not alter the configuration of the Belkin at all (having reset factory defaults beforehand), mainly because although I could access the internet from my PC and my mobile, I could not access the IP address of the router, presumably because the properties of the local area connection on my PC remained unchanged with the IP address (188.8.131.52), Subnet Mask (255.255.255.0), Default Gateway (184.108.40.206) and 3 DNS addresses (220.127.116.11) (10.30.0.1) (18.104.22.168) as they were before hooking up the Belkin. The IP address the mobile received through WIFI on connecting to the Belkin was 22.214.171.124
I was not unduly concerned about not being able to access the configuration of the router as everything was working as I had hoped it would and even when I powered off my PC I still had internet access on my mobile. On rebooting the PC, however, I found that the router changed the DNS addresses on the PC to 2 only, both identical (192.168.2.1) and the IP on the mobile was allocated 192.168.2.2 Although I could still access the internet on my PC, I no longer had access from my mobile although the WIFI connection to the Belkin showed as being 'excellent'. When I did a 'repair' of my internet connection, hoping to revert to a fully operative state, the PC configuration changed again as follows: IP address becomes that of the router (192.168.2.1), Subnet Mask (255.255.255.0), Default Gateway (192.168.2.1), 2 DNS addresses (192.168.2.1) and the IP address allocated to my mobile remains (192.168.2.2) This configuration means I have no internet access from either PC or phone, but CAN access the router configuration. I restored a usable operating state by unplugging the power from the router, transposing the cables in the LAN ports on the router (swapped cable from LAN1 to LAN2 and vice versa), turned off WIFI on mobile and waited a minute or two. When I powered the router back up and switched on mobile WIFI again, everything was restored to the original working state and I have, once again, access to internet on both PC and mobile. It is very frustrating, however, to keep performing this ritual and I wonder if any of you more technically minded, know a way to work around this, perhaps by manually changing the configuration of PC or router? I would certainly welcome any advice.
PS. Operating system is Windows XP - mobile is HTC Wildfire
Likes # 0
Posted March 13, 2013 at 1:51PM
Your basic problem is that you cannot use the Belkin as a router by connecting both Internet and devices to its LAN ports. It will behave as a network switch, not as a router, and only one connected device will have internet access. The fact that its DHCP server is still running and allocating 192.168.2.x addresses will mess things up even further.
Had you been using a Cable/DSL Router, which has an RJ45 ethernet port for its WAN (Internet) connection, this should work. Your WAN port is a telephone connection and the Modem and Router sections cannot be separated to allow you to use it as a stand-alone router.
Likes # 0
Posted March 13, 2013 at 10:24PM
Many thanks for you input mgmcc, I hear what you are saying about the router DHCP server and will try disabling it to see if this helps. I do not, however, agree your comment regarding the router acting as a network switch and giving me an 'either/or' internet connection as clearly this is not the case since I currently have a connection on both my PC and mobile. The problem is that the connections are not consistant, as detailed in my ealier post the PC ipconfig changes on reboot after shutdown, and the mobile IP address is reallocated to one that does not allow me internet access.
I will post an update after trying the DHCP disable. I suspect though that life would be a lot easier if I did as you suggest and acquired a more compatible router.
Your help is appreciated.
Likes # 0
Posted March 15, 2013 at 8:20PM
Problem resolved! I disabled the router's DHCP server and, following further advice, gave the router a static IP address of 192.168.0.254 with no Gateway and DNS. Simples!!! Works a treat - consistent internet access on both PC and mobile (still don't really understand why but just pleased the problem is resolved). I am one happy pensioner.
Reply to this topic
This thread has been locked.