failure to install xp on new motherboard

  wee willy wonker 17:43 15 Feb 06
Locked

Building a new system. New Asus P5gpl-x and Pentium 4 3GHZ 64bit (775 pin). Trying to install XP with SP1 onto new SATA harddrive. BIOS recognises all hardware.
Our problem - XP loads initial setup files and hangs when 'Starting Windows'. Any suggestions would be helpful as some hours have already passed on this.

Nick

  User-312386 17:46 15 Feb 06

did you load the sata drivers?

  wee willy wonker 17:56 15 Feb 06

No. Have tried installing xp on IDE harddrive and it still hangs. Can you load sata drivers without an operating system installed?

Thanks.

Nick.

  User-312386 20:56 15 Feb 06

I had this problem once and found for some unknown reason that having my speaker plugged in the back at the time of installation did this

Have you anything plugged in at the back such as USB printer or anything?

  rmcqua 21:16 15 Feb 06

It wouldn't get as far as loading the initial setup files if there was a SATA driver problem. Try installing with the absolute minimum of devices attached - just CD drive, HDD, mouse and keyboard.

  Fruit Bat /\0/\ 21:20 15 Feb 06

Installing XP on SATA drive
Once you have the drive(s) connected you are ready to start installing XP.
Master and Slave
Remember since it's serial you can only have one device per SATA port/cable so SATA drives don't have jumpers. On the Motherboard SATA1 Port is for the primary device, SATA2 port is for the secondary device etc.

SATA controller driver
Your Motherboard or SATA controller card requires a driver to work properly. If you did not get a Floppy Disk with the SATA driver included with your Motherboard you will have to make one. The SATA drivers can be located on the installation CD that came with your Motherboard or preferably, download the latest SATA controller drivers from the manufacturers site. Once you have located the drivers copy them to a formatted floppy disk. Make sure they are in the root directory i.e. not contained within any folders.

BIOS settings
When you turn on the PC hit the Delete key when prompted and you will enter the BIOS (Basic Input Output System). Here you set the first boot device to be the CDROM drive, the option is usually found under the Advanced Options section but this depends on your BIOS and you may have to look around for it. Once you have done this save and exit.

Installing the SATA controller driver
Once you have set the PC to boot from the CD make sure the XP CD is in the CD drive and start the installation as per usual. Within the first minute or so of the installation Windows will prompt you to press F6 to install RAID or SCSI drivers, do this. Windows will continue to install then ask you to locate the driver. now with the floppy disk created earlier in drive A: select the driver and hit Enter.
With the SATA drivers installed you can now continue the Windows installation as usual.

BIOS settings revisited
Once Windows has finished installing you will need to make sure the PC is set to boot from the SATA drive. To do this make the first boot device SATA if the option is available.If not you have two options: HD0 - If there are no IDE HDs present, or SCSI if you do plan on running an IDE HD as a secondary device.

1. have you installed onto the primary SATA drive?

2. have you reset the BIOS to boot from SATA (SCSI) drive?

This thread is now locked and can not be replied to.

Sony Xperia XZ Premium review: Hands-on with the new 4K HDR phone with Motion Eye camera and Snapdr5…

1995-2015: How technology has changed the world in 20 years

Best laptop for design and art 2017: we test Apple, Dell, HP, Lenovo and Microsoft's best models…

CarPlay tips & troubleshooting guide: CarPlay tips & troubleshooting guide: Get the most from…