Satellite cable splitter.

  rdave13 16:11 PM 24 Jul 10
Locked

I'm using a Sky box as freesat and thinking of buying a cheap freesat box for HD viewing. Does a splitter reduce the signal if one box is always off while the other is used? If there is such a thing would a swich be better? Dont fancy having an extra cable into the house. Thanks for any advice.

  Chris the Ancient 18:45 PM 24 Jul 10

If the splitter is a 'passive' one (no amp or power into it), yes, there will be a drop in signal strength - whatever the state of the other box.

A simple switch would not be that simple in that the shielding would become unbalanced and cause a bit of loss of signal quality (unless you can find some form of rf switch.)

CtA

  rdave13 19:27 PM 24 Jul 10

Wondering if something like this would work; click here
need to scroll down to the grey amps with f-connectors at £18.50 ?

  wiz-king 20:43 PM 24 Jul 10

Loss 4.0dB thats quite a loss if your signal is not good. You need also to consider whether it has DC continuity if you are feeding from a dish (Im nor sure the one in the link does).I would try the plain metal one, internal loss 4.0dB thats not too much of a loss if your signal is good.

  wiz-king 20:44 PM 24 Jul 10

Oops ignore the first sentance - I meant to delete it!

  rdave13 20:57 PM 24 Jul 10

Thanks for pointing out the loss.Same as an ordinary splitter. Signal isn't that good, strength is 3/4 the way on the bar and quality is just over half on the bar on the Sky signal test.
I really don't want another cable trailing the floor but it isn't looking good is it? Thanks both for your replies. Can you suggest another possibility?
Google isn't very helpful this time.

  BRYNIT 22:49 PM 24 Jul 10

You cannot split the signal between two sat boxes from 1 LNB you will need a twin LNB.

A little information on how an LNB works.

  rdave13 23:03 PM 24 Jul 10

Thanks for your response. I was fearing that and if you did split the digital signal it would be dire.
Could you supply a link to the information, I'd be very grateful.
As a 'fiddler' I might still pursue this problem.
Oh for analogue!

  dms_05 10:02 AM 25 Jul 10

You need at least one feed from an LNB for each receiver. It has nothing to do with the loss of signal strength. Each receiver will output two possible voltages to the LNB - either 13v or 18v - and this selects the polarisation of either H or V. Also each receiver will output a 22KHz tone to switch between low and high range of frequencies. So if you split the LNB feed you will have the possibility of any combination of the voltage/tone been applied by either box.

The only solution is a multi output LNB so each receiver has its own feed. You can pick a Quad output LNB (as used by Sky for HD+) on ebay for under a tenner.

  amonra 10:53 AM 25 Jul 10

As dms_05 has stated, LNBs are so cheap it's not worth the hassle of trying to split and isolate an existing single feed. I think Lidl was selling a suitable one recently for around £10. It's a simple job providing you can access the dish easily. Good luck.

  rdave13 11:24 AM 25 Jul 10

Thank you all for your advice. Much appreciated. Looks like a new LNB and running another cable.

Advertisement

This thread is now locked and can not be replied to.

How to watch iPhone 6s, iPhone 6s Plus launch live: What to expect from Apple's 9 September 2015…

1995-2015: How technology has changed the world in 20 years

This installation lets you control a laser and sound show using your mind

Apple's special event invitations decoded: A look back at 13 of Apple's most cryptic invites